Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Blog Article
Right here in the next paragraph you will discover some sensible points involving Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough task. If the old tub is conveniently obtainable, the job can relocate speedily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will need an assistant to vacate the old tub as well as set in the brand-new one. Make sure you have qualified yourself for the work and are comfortable attempting it. As opposed to hiring a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This short article will certainly help you mount a new bathtub in your washroom if you have currently purchased a brand-new tub and don't need to change the arrangement of your previous supply of water pipes.
Your devices as well as product list need to comprise the following:
Getting ready for the Installation
Firstly, the sustaining frame supplied with the bathroom should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipes. When the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using both wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the tub up until the spirit level reads degree.
To install taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints and also new pipework for leakages and also tighten them if necessary. Load the bath tub and likewise check the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the tub should wait till the bathtub has been utilized at least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Protect the tap in position with the maker provided backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind should be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack a stiff seal, causing the water to pass through the wall between the bathroom and also the tiling, bring about issues with dampness and also feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealer can split fairly early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for finding the time to browse our blog post. Enjoyed our blog? Please share it. Help another person find it. I am grateful for your time. Visit again soon.
Act now! Report this page